Electrical
Showing 1–16 of 173 results
-
₦14,000.00₦12,500.00Quick ViewCOLEMAN cables is in line with its context and strategic direction which is committed to the manufacturing of quality electrical/telecommunications wires and cables that meet and exceed customers’ expectation, consistent with relevant stakeholders and ISO 9001:2015 requirements.
-
Quick ViewDigital panel indicator ENTES MPR-46S-96
Technical data
Type (manufacturer’s type) MPR-46S-96 Weight 315 g The height of the product 96 mm The length of the product 56 mm The width of the product 96 mm Type of meter attachment Panel meter, digital The minimum supply voltage 185 volts Maximum power supply voltage 265 V -
Quick ViewDKM 405 Network Analyser
True RMS measurements, 0.5% accuracy
• Total harmonic distortion display
• Max demand display
• Configurable relay output
• Energy pulse output capability
• Optically isolated, configurable digital input
• Active-reactive power counters
• Hour counter
• Voltage transformer ratio for MV applications
• Front panel programming
• Reduced panel depth
• Wide operating temperature range
• Sealed front panel (IP54)
• Plug-in connection system -
Quick ViewAutomatic Mains Fail panels are used where the local utility mains supply is backed up by an appropriately sized generator. The AMF panel monitors the local mains supply; if this supply should fail, or fall outside preset limits the AMF panel will control the pre-heating, fuel solenoid and starting of the generator. The AMF panel will then control the switching of the load from the local supply to the generator. Whilst the generator is running the AMF panel will monitor vital engine and alternator parameters safely stopping the generator should a fault condition occur. On return of the local supply the AMF panel will monitor the Supply to ensure it is stable and then transfer the load from the generator back to the local supply. The AMF panel will run the generator on for a pre-determined time to allow for any cool down periods required for the generating set. Once this time has elapsed the AMF panel will control the stopping of the generator.
All our AMF panels use the latest microprocessor controlled modules to enhance and provide maximum functionality. Various timers are included in the controller to prevent nuisance starting of the generator due to minor breaks in the local supply.
AMF panels are located at, and fitted to, the generator. If this does not fit with your infrastructure and wish for generator control to be located away from the site of the generator then a suitable automatic switch transfer is a better option.
-
Quick ViewAUTOMATIC TRANSFER SWITCH (ATS) MAINS-GENERATOR
Our generator Automatic transfer switch (ATS) panels or Changeover Panels are specified by the size in amps and the required control module, new control module updates are released regularly so please enquire if you do not see the configuration or manufacturer you require.
All panels use the highest quality switch gear and can be amended to your specification. Please note additions’ may require a larger enclosure.
We supply both single phase ATS for residential use and also three phase ATS for commercial or industrial applications.
-
Quick ViewPower 220V AC 22mm Digital Display Ampermeter Monitor Current Indicator Signal Light Ammeter Tester Measuring 0-50A Ampere Meter
Description:100% brand new and high qualityMaterial: Electrical componentsColor: Red/White/Blue/Green/Orange22 MM Digital Display Current Lights Combo AC 0-50A IndicatorSize: 2.8*5cm/1.10″*1.97″ (D*H)No retail packageQuantity:1 piecePackage Included:1Pc x 22MM 0-50A AC Current Indicator1Pc x Current Transformer Coil -
Quick ViewCAPACITOR SWITCHING CONTACTORS
Capacitor Switching Contacts conforms to IEC / EN 60947 – 1 and IEC / EN 60947 – 4. Ratings are available from 2.5kVAR to 75 kVAR.
TECHNICAL SPECIFICATION:
- Conforms to IEC/EN 60947-1 / 4
- Ratings from 2.5 kVAR – 75 kVAR
- Utilization category – AC 6b
- Early make contacts with damping resistors
- Ambient operating temperatures up to 550C
- Various coil voltage options
-
Quick ViewThe MFR012 is designed to control the relative air humidity inside of enclosures. When connected to an enclosure heater, (de-humidifier), it will turn the heater on at the set humidity level in order to raise the dew point. This helps prevent damage and malfunction of electronic components caused by condensation and corrosion. The MFR012 can also be used to control cooling fans, warning lights or other devices.
SPECIFICATIONS
Adjustment Range: 35 to 95% (±3.0%) relative humidity Switching Difference (Hysteresis): Approx. 4% RH @ 50% relative humidity
Permissible Air Velocity: 50 ft/sec (15 m/s)
Maximum Switching Voltage: 250 Vac
Attention: 250 V should only be switched in a non-condensing environment
Contact Type: Change-over contact
Contact Resistance: <10 mΩ
Service Life: 100,000 cycles
Minimum Switching Capacity: 100 mA @ AC/DC 20 V
Maximum Switching Capacity: 5A @ AC 230V (resistive load), 1.0A @ AC 230V (inductive load at cos j = 0.8); DC 20W
EMI/EMC Compliance: EN 55014-1-2, EN 61000-3-2, EN 61000-3-3
Connection: 3-pole terminal, 3 x AWG 14 max [2.5 mm2 (0.1 in2)]
Mounting: Clip for 35mm (1.4″) DIN rail (EN 50022)
Dimensions: 67H x 50W x 38 mmD (2.64 x 1.97 x 1.5″)
Housing: Clip for 35mm DIN rail (EN 50022)
Weight: 60g (2oz)
Operating Temperature: 0 to 60°C (32 to 140°F)
Storage Temperature: -20 to 80°C (-4 to 176°F)
Protection Type: NEMA 2 (IP20)
Application Examples:
• Electrical and Electronic Enclosures
• Telecommunication Systems
• Display Panels
• Ticket Dispensers
• Automatic Teller Machines (ATM’s)
• Access and Parking Control Systems
